Bob Smith Industries BSI-142 Clear Foam-Cure, Craft Glue, 4 oz

Bob Smith Industries BSI-142 Clear Foam-Cure, Craft Glue, 4 oz

FOAM-CURE is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed it’s curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner. Directions in 5 different languages.

  • Color: Clear
  • Brand: Bob Smith Industries
  • ASIN: B011XWDTOW
  • UPC: 707336142007

Bob Smith Industries BSI-139H Clear Super-Gold Odorless Foam Safe Super Glue, 1 oz.

Bob Smith Industries BSI-139H Clear Super-Gold Odorless Foam Safe Super Glue, 1 oz.

Super glues produce fumes that can be irritating to the eyes and nose. While not toxic, some people can be sensitized to these fumes. Super-gold+ is an odorless form of Super glue that gives the same high performance characteristics as bsi's INSTA-CURE+ without the irritating fumes. Super-gold+ will not fog Clear plastic and glass, and it can be used on all foams. It is the best all-around Super glue on the market.

  • Color: Clear
  • Brand: Bob Smith Industries
  • ASIN: B01FWZNQ1M
  • UPC: 007336139084

1 X BSI 142 Foam Cure 4 oz

1 X BSI 142 Foam Cure 4 oz

BSI142 EPP Foam Glue 4oz by Bob Smith Industries. Superior glue for EPP foam airplanes that will not melt or discolor the foam.

  • Brand: Bob Smith Ind Glue
  • ASIN: B00DT86A86
  • UPC: 707336142007

Wisemen Trading, Bob Smith Industries Epoxy 9oz (Slow-Cure)

Wisemen Trading, Bob Smith Industries Epoxy 9oz (Slow-Cure)

SLOW-CURETM 30 min. epoxy works best for forming reinforcing fillets on joints. It has the highest strength of our epoxies. It is waterproof and more heat resistant. SLOW-CURETM can be used for bonding if you're willing to wait overnight. Fillers such as microballoons can be mixed with SLOW-CURETM and FINISH-CURETM to form a putty-like consistency. Such fillers will usually decrease the working time by about 25%. Bonded objects can be handled after 8 hours and the cured epoxy reaches full strength within 24 hours. MID-CURETM 15 min. epoxy is used in larger areas where more working time is needed. It is more water resistant and can be used as a substitute for QUIK-CURETM in most applications. MID-CURETM is our most flexible epoxy and is ideal for gluing to fiberglass surfaces. Allow 45 minutes before handling parts and 2 hours for full strength. UIK-CURETM 5 min. epoxy cures to a slightly flexible consistency. This lack of brittleness allows it to form a lasting bond in areas subjected to high vibration or stress. QUIK-CURETM shouldn't be used in areas that are subject to long-term immersion in water; however, it works fine for the internal structure of wood framed boats. QUIKCURETM is our only epoxy on which you can apply polyester resins. It can be mixed with microballoons to fo...

  • Brand: wisemen trading
  • ASIN: B01J58ULA6
  • UPC: 788490111276

Finish-cure 20min epoxy 4.5oz Bob Smith Ind.

Finish-cure 20min epoxy 4.5oz Bob Smith Ind.

These epoxies are specifically used for laminating or for glass or Graphite lay-up. They have excellent wetting qualities and are easily spread. Pot life is 20 minutes for Finish-Cure, with full strength in 8 to 24 hrs. These epoxies are fully compatible with foam too. FEATURES: Results in a clear finish, resistant to most chemicals, and able towithstand up to 2500lbs. per sq. inch of pressure. YOU WILL RECEIVE: One 4.5oz bottle of epoxyOne 4.5oz bottle of hardener(9oz combined)

  • Brand: BSI
  • ASIN: B001NIC3VW
  • UPC: 707336209007

BSI Glues: Insta-Set Aerosol Accelerator (4.4 Fl. oz.)

BSI Glues: Insta-Set Aerosol Accelerator (4.4 Fl. oz.)

INSTA SET AEROSOL ACCELERATOR

  • Brand: Pen Kit Mall
  • ASIN: B072VQPBHZ

Bob Smith Industries 141 Foam Cure, 1 oz

Bob Smith Industries 141 Foam Cure, 1 oz

FOAM-CURE is a silicone based adhesive that works very well on EPP and EPO foams. It is crystal clear and cures to a more flexible consistency than CA. It is, however, not instant bonding like CA and there is no accelerator to speed its curing. To obtain a faster initial bond when bonding two pieces, FOAM-CURE can be applied to one piece and after the two are joined, they can then be pulled apart. After letting it air dry for about ten minutes, FOAM-CURE will act like a contact cement when the parts are rejoined, resulting in enough tack strength to allow the next steps of assembly. Full strength is reached in 10-12 hours. FOAM-CURE works with all foams, and will actually bond most other materials. It will bond wood and plastic to foam, and is a good canopy glue. FOAM-CURE does not, however, cure flexible enough to act as a hinge for aircraft control surfaces. Its limitations occur when bonding large areas of two non-porous materials. FOAM-CURE requires exposure to air for drying. If one tried to bond, for example, a half-dollar coin to glass, over 90% of the adhesive would never cure, since the solvent it contains would have no where to evaporate. A small amount of denatured alcohol can be mixed into the Foam-Cure to make it thinner.

  • Brand: Bob Smith Industries
  • ASIN: B00DT85IXO
  • UPC: 707336141000

Bob Smith 151 Insta-Set 2oz Accelerator

Bob Smith 151 Insta-Set 2oz Accelerator

This is 2oz bottle of INSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. FEATURES: Formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strengthWill not craze most plastics even clear plastic and white foam. Forces the immediate cure of all cyanoacrylates Expands gap filling ability Permits structural fillet forming Solves most tough-to-bond combinations of materials Safe for use with plastics YOU WILL RECEIVE: One bottle of 2oz bottle of INSTA-SETOne pump REQUIREMENTS: Use with CA glues SPECIFICATIONS: 2 fl oz. (59.1ml)

  • Brand: Bob Smith Industries
  • ASIN: B0000DD1QR
  • UPC: 696747842340

Super-gold thin odorless 1oz Bob Smith Ind.

Super-gold thin odorless 1oz Bob Smith Ind.

Super-Gold Odorless 1oz CA Adhesive GlueSUPER-GOLD and SUPER-GOLD+ are our odorless INSTA-CURE CAs They are non-frosting and take only 2 or 3 seconds longer to bond. There are no fumes that irritate the nose and eyes. The SUPER-GOLDs do not attack white foam; therefore, they can be used in the building of foam core wings and the assembly and repair of plastic and foam ARFs. They will not fog clear plastic. SUPER-GOLD+ is ideal for attaching clear canopies in plastic model kits; however, MAXI-CURE is still recommended for assembling the rest of plastic kits. Wood can be bonded to white foam with SUPER-GOLD + in less than fifteen seconds. For bonding foam to foam, spray a very light fog of INSTA-SET to one piece and apply SUPER-GOLD+ to the other before joining. Excess INSTA-SET may create too much heat, which can melt the foam. Both SUPER-GOLDs cure to a more flexible consistency for better shock absorbtion. Whenever a large amount of CA is to be used in such applications as saturating fiberglass or Kevlar, SUPER-GOLD eliminates the irritating fumes from the evaporating monomer that make repeated use of CA unpleasant at times.

  • Brand: Bob Smith Ind Glue
  • ASIN: B0000DD1QJ
  • UPC: 707336122009

Bob Smith Industries 3/4 oz Ultra-Cure RC Tire Glue Pocket 2 Pack #BSI130

Bob Smith Industries 3/4 oz Ultra-Cure RC Tire Glue Pocket 2 Pack #BSI130

Bob Smith Industries 3/4 oz Ultra-Cure RC Tire Glue Pocket 2 Pack #BSI130

  • Brand: Bob Smith Industries
  • ASIN: B01MAU005R
Similar Bob Smith Foam Cure Results
Bob Smith Foam Cure Video Results

BOB SMITH INDUSTRIES SUPER GOLD+ FOAM GLUE

Bob Smith Foam Cure

We explore Bob Smith Industries line of glues and show you the consequences of using non-foam safe and foam safe glue and how to properly bind two pieces of foam using Bob Smith Industries' Super Gold+ Glue, while adhering Insta-Set Accelerator during the process. Visit us online at http://www.m...

  • Likes: 16
  • View count: 3932
  • Dislikes: 0
  • Comments: 1
Tags: Foam Glue,Bob Smith Industries

Bob Smith Industries Glue Explained...

Bob Smith Foam Cure

http://eugenetoyandhobby.com/product-tag/bob-smith-industries/ What we have done here is broken down the most popular Bob Smith Industry glue's in our store and explained which is best for each intended use. Enjoy and good luck in all your hobby projects(some of these might work for parents wit...

  • Likes: 23
  • View count: 3834
  • Dislikes: 2
  • Comments: 4
Tags: Bob,smith,industries,glue,explaned,explained,simple,uses,history,hobby,toy,fix,repair,build,build...

Bob Smith Industries Insta-Cure, Insta-Cure+ and Maxi-Cure CA Comparison by ModelMerchants.com

Bob Smith Foam Cure

We compare Bob Smith Industries' three main types of Cyanoacrylate glues (Insta-Cure, Insta-Cure+ and Maxi-Cure) and explain the differences between them, along with a few demonstrations of the types of applications you can use each one for. For a special discount, click the link below. Visit us...

  • Likes: 28
  • View count: 2368
  • Dislikes: 0
  • Comments: 1
Tags: Bob Smith Industries,Bob Smith Industries Maxi-Cure,Bob Smith Industries Insta-Cure,Bob Smith Ind...

How to Fix / Repair Peeling Foam from Ski Goggles

Bob Smith Foam Cure

Presented by ModelMerchants.com In this video, we showcase how Bob Smith Industries' Flexible Foam Cure glue can be used to adhere / repair foam separating from the frame of ski / snowboard goggles. It's an EPP and EPO based foam glue and instead of it being water based, you don't have to worry ...

  • Likes: 39
  • View count: 14586
  • Dislikes: 1
  • Comments: 8
Tags: Ski Goggle Repair,Foam Safe Glue,Bob Smith Industries,Flexible Foam-Cure Glue